Nov 16, 2026 · 5 min read

Sawmill Recovery Percentage: How to Calculate It and Why It Varies

Timbba report of sawing by species, hardwood and pine

Sawmill recovery percentage is the volume of sawn timber you get from a lot of logs, divided by the volume of those logs, multiplied by 100. If 100 CFT of logs gives 62 CFT of boards, your recovery is 62%. The number only means something when the log volume and the sawn volume are measured the same way every time, and that is where most mills go wrong.

This guide shows how to work out the sawmill recovery percentage for one log and for a week of sawing, what a fair comparison looks like, and which causes move the figure.

The formula, step by step

There are three steps, and each one needs a number you can check.

  1. Measure the log volume in CFT by the quarter girth (Hoppus) method: girth in inches x girth in inches x length in feet / 2304.
  2. Measure the sawn output in CFT: length in feet x width in inches x thickness in inches / 144 for each piece, added up.
  3. Divide output by input and multiply by 100.

If you work in metres, 1 CBM is 35.3147 CFT, so convert once and keep everything in one unit. The log CFT calculator does the log and sawn-timber arithmetic and the CBM conversion if you want to check a figure by hand.

A worked example, one log

This is an example with round figures, not a real mill. A pine log has a girth of 60 inches and a length of 12 feet.

Log volume: 60 x 60 x 12 / 2304 = 43,200 / 2304 = 18.75 CFT.

The log is sawn into the pieces below, all 12 feet long.

Size Pieces CFT per piece CFT
6 x 2 in 6 1.000 6.00
4 x 2 in 6 0.667 4.00
3 x 1 in 8 0.250 2.00
Total 20 12.00

Recovery: 12.00 / 18.75 x 100 = 64.0%. The other 6.75 CFT, 36% of the log as measured, went out as slabs, edgings, sawdust and trimmed ends.

Measure input and output on the same basis

The quarter girth method gives about 78.5% of the log’s true round volume. That is deliberate, because it allows for bark and for the waste of squaring the log. The effect on recovery is large. A mill that gets 50% of the true round volume will show about 64% when the same logs are measured by quarter girth.

So a recovery figure is only comparable with another figure that uses the same method. Three habits cause most of the confusion:

  • Comparing your quarter girth recovery with a figure quoted for true volume, or the other way round.
  • Taking the log volume from the supplier’s list, which may be on a diameter scale, and the output from your own tally.
  • Counting sawn output before trimming and drying in one week and after it in another.

Pick one basis, write it at the top of the register, and keep it.

Track sawmill recovery percentage by lot, not by month

A monthly figure for the whole mill hides the answers you need. A mill running pine and hardwood on two saws can post a steady 60% while one saw drifts down and the other drifts up. Work it out for each lot you saw, then add up the lots.

Here is a week of one consignment on one saw, again as an example with round figures.

Item CFT
Logs sawn, measured at the saw 240
Sawn output into stock 150
Not recovered (slabs, edgings, sawdust) 90
Recovery 150 / 240 = 62.5%

Now see what a small change is worth. Suppose a mill saws 10,000 CFT of logs a month and lifts recovery by 2 percentage points. That is 200 CFT more boards from the same logs. At ₹1,000 a CFT, an example price, it is ₹2,00,000 a month, with no extra log bought.

What moves the recovery percentage

  • Log shape and size. Straight, round logs of good girth yield more than crooked or small ones. Report recovery by girth band if you saw a wide range.
  • Species and hollow. Hardwood logs lose wood to hollow, heart cracks and defects that a tape does not show. Compare like with like, and do not judge a teak lot by a pine yardstick.
  • Sawing pattern. What you cut the log into decides what is left over. Sawing 3 x 1 strips from a 12 ft log recovers differently from sawing 6 x 2 planks.
  • The machine and its set-up. A worn or poorly set blade wanders and widens the cut, and every cut turns wood into dust. Compare machines on the same kind of log.
  • The operator. Two operators on the same saw can differ, because each decides how to open the log and how much to trim.
  • The measurement itself. A girth tape pulled tight or a length taken to the nearest foot moves the input. Part of what looks like low recovery is a bad input figure.

How to read a low figure

Do not start by blaming the saw. First ask whether the input is right. If the log was bought as 28 cm and measured at 25 cm at the machine, the output will look poor against the bought volume, but the mill has not lost anything it ever had. Separate the two numbers: variation between purchase and mill measurement, and recovery from the mill measurement to the boards. If you mix them you will argue with the supplier about a loss that belongs to the saw, or the other way round.

A short routine works for most mills:

  1. Record the log’s girth and length at the saw, against the lot it belongs to.
  2. Record the sawn output by size at the end of each shift.
  3. Work out recovery for each lot each week.
  4. Look at the lots well below the average and ask what they have in common: supplier, species, machine or operator.

How Timbba does it

In Timbba’s sawmill software, the operator scans the log at the saw and types only what the mill measured. What the log was bought as is already there from the supplier’s list, so purchase and mill figures sit side by side without copying. The sawn output goes into stock by species, size and yard, and the owner sees variation and recovery per machine and grade on the dashboard each morning. The same record runs on through stock, orders and dispatch in Timbba’s timber management software.

Want to see recovery on your own logs and saws? Book a demo and we will use one of your real consignments.

Get in touch

See it on your own consignment.

Send us a supplier's list and we will show you the gate, the mill and the reports running on your logs — a 45-minute call, no hardware to buy.

Call us+91 74281 37755 WhatsAppMessage us
OfficeA-24, Fourth Floor, Sector 63, Noida, India 201301

An e-mail or a phone number is enough. We reply within one working day.