Timbba

Sawmill Recovery Estimator

See what a log should give before you saw it, and the best way to cut the sizes you want.

  1. The Log
  2. Estimate
  3. Your Sizes
  4. Best Way To Cut

Tell Us About The Log

How Straight Is It?
More About The Log (optional)
Wood Lost To Rot, Cracks Or Big Knots
The Saw

What We Have Assumed: the log narrows by 1 cm for every metre of length, 8% is lost to end trimming and sawing variation, a saw cut is 2 mm (thin band saw), 3 mm (band saw) or 6 mm (circular saw) wide, and only whole pieces are counted. Your mill may differ.

More Free Tools:Log CFT CalculatorRecovery Value CalculatorAll Free Tools

Why Recovery Is Never 100%

A board is a rectangle and a log is a circle. Whatever size you cut, the rounded outside comes off as slabs and edgings, every saw cut turns a strip of wood into dust, and the log is narrower at one end than the other. Those three are there in a perfect log on a perfect saw. A bend, a hollow or rot takes more.

What Moves The Recovery You Can Expect

The size of the log. A thicker log loses a smaller share of itself to the rounded outside, so recovery rises with girth. Sawing studies in several countries agree on this more than on anything else.

The size you cut. The same log gives a different recovery for a different size, because what matters is how many whole pieces fit across it. A size that leaves a wide strip unused at the edge recovers less than one that fills the log. Try two sizes on the same log above and compare, then add a smaller second size and watch the figure rise.

How straight it is. A straight cut through a bent log misses wood on the inside of the bend. A published sawing simulation found that timber out falls by 5 to 7% for each tenth of the log’s diameter that it bends, and the estimator uses 6%.

The saw. Each cut removes its own width. A thin band saw takes about 2 mm, an ordinary band saw about 3 mm and a circular saw about 6 mm. The difference grows with the number of cuts, so it matters most on thin boards.

Taper. The girth is taken at the middle, but whole pieces must fit the small end. The estimator assumes the log loses 1 cm of diameter for each metre of length.

Knots and grade. Knots mostly lower the grade and the price of the timber, not the volume you get. Rot, wide cracks and very large knots do cost volume, which is what the defects choice is for.

For a sense of scale, a study of 215 chir pine logs in Uttarakhand found an average sawn outturn of about 70% of the quarter girth volume, ranging from about 60% to 85% with the girth of the log and the size cut.

How The Estimate Is Made

It works in two steps. With only the log entered, there is no single honest figure, because recovery depends on what you cut. So the first answer is a range for common plank sizes: the lower figure is one size cut alone, the higher one a mix that fills the edges of the log. Add the sizes you want and the range becomes one figure, with the number of each size.

The estimator works out the diameter of the log from its girth and takes off the taper to reach the small end. A JAS diameter is already the small end. It then lays your sizes across that circle in rows, leaving the width of a saw cut between pieces, and counts only whole pieces.

The drawing shows the small end of the log with each piece where it is cut. When a size is shorter than the log, a second drawing shows the log from the side, with each length cut into the lengths you asked for and any offcut left over.

Each size has a length too. Leave it empty for pieces as long as the log. Give a shorter length and the estimator cuts each stick end to end: a 12 ft log gives two 6 ft pieces from every place in the layout, and a shorter size of the same section can use what a longer one leaves.

With more than one size it does not cut them in the order you typed. It tries the ways of stacking the rows and of filling each row, with each size flat or on edge, and keeps the arrangement that turns the most of the log into timber. That is the number of each size it shows.

Small sizes always fill a round log better than large ones, so the mix with the most timber can leave out your largest size. If that size is the one you are sawing for, choose My first size first: the estimator then cuts as many of the first size as the log allows and fills what is left with the others.

It then takes off a share for a bend, for the defects you chose and 8% for end trimming and sawing variation, and compares the result with the log’s volume.

recovery % = sawn timber out ÷ log volume × 100

The log volume is the one the log was measured by. For a girth that is quarter girth (Hoppus), the figure the trade buys and sells by. For a JAS diameter it is the JAS volume. Quarter girth counts about 78.5% of a log’s true round volume, so the same sawing reads higher against it than against true volume: 50% of the true volume shows as about 64% on quarter girth. The estimator gives both. To work out a log’s volume on its own, use the log CFT calculator.

What 1% More Recovery Is Worth

A small change in recovery is a large amount of timber over a month, because it applies to every log you saw. One percent more recovery means one more CFT of sawn timber from every 100 CFT of logs.

extra sawn timber = logs sawn a month × change in recovery ÷ 100

On 10,000 CFT of logs a month, moving from 62% to 64% is 200 CFT more sawn timber from the same logs. At ₹1,000 a CFT that is ₹2,00,000 a month, with no extra log bought. Put your own figures in the Recovery Value Calculator.

To compare the estimate with what a lot really gave, the blog has a guide to measuring it: how to calculate sawmill recovery percentage and why it varies.

एक लट्ठे से कितनी चिरान निकलेगी

लट्ठे की गोलाई और लंबाई भरें, बताएँ कि वह कितना सीधा है, और जो साइज़ चाहिए वह लिखें। एस्टिमेटर बताएगा कि उस साइज़ के लगभग कितने पीस निकलेंगे और रिकवरी कितने प्रतिशत रहेगी। रिकवरी कभी 100% नहीं होती, क्योंकि गोल लट्ठे से चौकोर पीस काटने में छिलका, बुरादा और किनारे की कतरन निकल ही जाती है।

Questions

How many pieces of a size can I get from a log?

It depends on how many whole pieces fit across the small end of the log once a saw cut is left between them. Enter the girth and the length, add the size you want, and the estimator counts them. A straight log of 48 inches girth and 12 feet, cut into planks 50 mm thick and 6 inches wide on a band saw, should give 8 pieces.

Can the pieces be shorter than the log?

Yes. Each size has a length. Leave it empty for pieces as long as the log, or enter the length you want. A 12 ft log gives two 6 ft pieces from every place in the layout. If a size is 8 ft, the 4 ft left over is waste unless another size of the same thickness and width can use it.

Why does it show a range before I add sizes?

Because recovery depends on what you cut, and with only the log entered the estimator does not know that yet. The lower figure is one common plank size cut alone and the higher one is a mix of common sizes that fills the edges of the log. Add your own sizes to get one figure.

I want two or three sizes from one log. How many of each should I cut?

Add each size and the estimator works it out. It tries the ways of arranging those sizes across the small end of the log and keeps the arrangement that turns the most of the log into timber, then tells you how many of each size that is. If one size matters most to you, choose My first size first and it cuts as many of that as the log allows before the others.

How is the expected recovery worked out?

From the shape of the log. The estimator lays the sizes you want across the small end of the log, with a saw cut between pieces, and counts the whole pieces that fit. It then allows for a bend, for the defects you tell it about and for end trimming, and compares the sawn timber with the log’s volume. It is an estimate: a careful sawyer with a sharp blade can beat it, and a worn blade or a careless cut will fall short.

Why can recovery never be 100%?

Because a board is a rectangle and a log is a circle. The rounded outside comes off as slabs and edgings, every saw cut turns a strip of wood into dust, and the log is narrower at one end than the other. That is true of a perfect log on a perfect saw. A bend, a hollow or rot takes more.

Does recovery change with the size I cut?

Yes. Recovery depends on how many whole pieces of that size fit across the log. Two sizes cut from the same log can differ by ten points or more, and thin boards lose more to sawdust because there are more cuts. Adding a second, smaller size to use what the first leaves at the edges raises it.

Do knots and grade change the recovery?

Mostly they change the grade and the price of the timber, not the volume you get. Rot, wide cracks and very large knots do cost volume. Use the defects choice to allow for those.

Why is the figure higher than I expected?

Usually because of how the log is measured. The quarter girth (Hoppus) method counts about 78.5% of a log’s true round volume, so recovery against quarter girth volume reads higher than recovery against true volume. The estimator shows both.

How much is 1% more recovery worth?

Multiply the log volume you saw in a month by the change in recovery, divide by 100, and price the extra sawn timber. On 10,000 CFT of logs a month, moving from 62% to 64% is 200 CFT more sawn timber from the same logs. At ₹1,000 a CFT that is ₹2,00,000 a month.

Does the estimator send my figures anywhere?

No. The sums run in your browser. Nothing you type leaves your phone or computer unless you share the link yourself.

Want The Real Figure For Every Log?

Timbba records each log at the saw and the timber that comes off it, so what went in against what came out is there per machine and per consignment.